|Product Name:||Ship Launching Docking Inflatable Boat Airbags Marine Rubber Airbag||Size:||D1.5L15m 8layers|
|Material:||Natural Rubber||Application:||Ship Launching, Docking, Lifting, Salvage, Etc|
|Certificate:||ISO, BV, CCS, RS, IRS||Service Life:||6-8 Years|
Docking Inflatable Boat Airbags,
Ship Launching Inflatable Boat Airbags,
D1.5L15m Marine Rubber Airbag
Ship Launching Docking Inflatable Boat Airbags Marine Rubber Airbag
Overview of ship launching airbags
1. Qingdao Florescence specializes in the production of ship rubber airbags since 1992.
2. Rubber airbags use the best materials (Thailand natural rubber RSS3) and can reuse for 6-8years without misuse.
3. Our factory paid attention on product quality for over 30 years to make sure our customers use well.
4. Wear resistance and anti aging airbag with ISO, CCS, BV, IRS, RS, etc certificate.
5. Need no more than air compressors, winches and ropes. Much cheaper and more portable than other methods.
6. We support customer worldwide, such as America, Philippines, Indonesia, UAE, Saudi Arabia, etc.
Material and accessories of inflatable rubber boat airbags
An inflatable rubber boat airbag is to be constructed of an outer rubber layer, one or more synthetic-tyre-cord layers, and an inner rubber layer. The arrangement of synthetic-tyre-cord reinforcement layers is shown in the picture below, all materials shall be vulcanized firmly.
Features of ship landing airbag
Special synthetic-tire-cord reinforcement make airbags stronger.
2.High lifting capacity
One piece bag can lift heavy structures ranging form 70 tons to 1,000 tons in weight. Normally, caissons up to 5,000 tons or up to 2,000 tons can be lift by our marine rubber airbags.
3.Steady roll movements
When airbags are taking the load, they can roll steadily with large contact area and less reaction force to secure a smooth transportation and relocation.
4.Easy to operation
Only compacted ground and minimum facilities such as trolleys are needed. Meanwhile, heavy lifting airbags are easy to install as the deflated airbags are very fat and small to be placed under vessel's hull.
Using airbags helps to decrease 70% budget comparing with traditional lifting methods.
Safety precaution of inflatable rubber boat balloon
1.Over pressure control:
Strictly control the operating pressure, over pressure is forbidden.
2.The landing slipway requirements:
The landing ground should be ground or cement concrete, according the tonnage of different ships.
3.Avoid sharp objects:
Make sure no sharp objects and smooth & clean ground during using airbags in case of any break.
4.Avoid distortion and overweight:
Avoid distortion in the length direction during rolling and avoid overweight load after gas charging.
Attentions during airbag use and ship launching
1.The airbags must be checked if the pressure gauge is normal before used.
2.The working pressure of the airbag when used should compare the data in the bearing capacity from mustn't use excessive pressure.
3.It must clean the sharp and protruding hard objects on the ground which could contact with the airbag body before the airbag being used, in case it punchures the skin of the airbag.
4.The distance of the airbag under the ship should no less than 1.5m,the distance after compression should at least 0.8m, in case it occours the airbag overlapping phenomenon when the ship launching.
5.Lifting after the airbag be forced under the snip, when most of the ship is raised up,demount the pier-top and force the rolling airbag at the same time. If there is one or two pier-top impacted which is difficult to take out, do not let the works force to demount the pier-top,if the pier-top is demounted, it is easy to suffer from the slip gravity, and then will make the airbag explosive. The workers should check the working pressure of the airbag.
Contact Person: Michelle Zhang
Tel: +86 053280689155