Payment & Shipping Terms:
|Work Press:||0.005-0.12mpa||Package:||Pallet Or Wooden Box|
|Application:||Used For Pouring The Hollow Of Large Reinforcd Concrete Structure||Warranty Period:||24 Months|
|Working Temperature:||-10 °C ~ +90 °C||Using Time:||More Than 60 Times|
Customized Length Of Column Formwork / Concrete Beam / Inflatable Rubber Balloon
Pneumatic rubber mandrel(Inflatable formwork)is a kind of cylinder bag that can expand, shrink, used to form concrete component of cavity. It is easy to be used, convenient and durable, is soft and can fold, curly, contraction when it isn't inflate, it have the enough strength to withstand the pressure of concrete when it is inflated, this is incomparable with any traditional template. it is used in reinforced concrete members, including stake, roof, roof board column, beam, building, water conservancy project (shipyards, slipway, dock). Construction practice proves that Inflatable rubber mandrel is simple, not only save materials, and has a shape characteristics,it could be round, oval, rectangle, vaulted, trapezoidal pipeline, etc. Also you can make a straight hole, etc, can make a building structure light, thin wall hollow, change the concrete performance have been used rigid characteristic template situation.
The performance characteristics of ARD inflatable rubber balloon
1. Design scientific and reasonable used inflatable rubber mandrel, or casting parts, finished product can meet the requirement of design, easy operation, save work, save time, save material.
2. Have good ageing resistance performance and long service life this product use synthetic rubber, natural rubber and strengthen layer vulcanize. Has very good resistance to bulge, flexibility and elasticity, so can satisfy all sorts of work in the conditions of use.
3. Widely applicable temperature , within the scope 10 °C ~ +90 °C of the material without change.
Standard specifications of ARD hose mandrel:
1> Diameter (D) : From 0.3m to 2.2 m.
2> Effective Length (EL) : From 6m to24m.
3> Total Length (TL) : From 7m to28m.
4> Other specification also available upon customer’s request.
Technical parameters of pipe mandrel:
Operating instruction manual ARD inflatable rubber balloon
Using of rubber inflatable mandrel:
1. Put the inflatable mandrel into the mold--pull inflatable mandrel into steel reinforcement cage,and make the vertical joints upward
2. Start inflatable for mandrel
(1) Open the valve and inflatable air to setted press,then close valve
(2) Working press(See the sheet)
(1)Because the inflatable mandrel will float upward when vibrated concrete,so you must fix up and down,and plus briquetting to overcome on buoyancy.
(2)For φ250mm mandrel,the normal stirrup spacing is 80cm. If the diameter increased,then the stirrup spacing will be reduced relatively.
4. Pouring of concrete
(1) The process of pouring of concrete is nearly same as solid constructed part
(2) Using high frequency plug-in vibrating rods from both sides at the same time vibrators can avoid the mandrel moving around
(3) The vibrating rod ends can not contact the mandrel, in case damaging the mandrel and leaking gas.
5. as the concrete component solidification then can empty gas from the cavity, pulled out the capsule.
6. Wash the mandrel,test pressure and inspect.Storage and maintenance of inflatable mandrel
A. After using,you need wash the mandrel cleanly with water; when don't need to use,please storage the mandrel in the place of ventilated and dry,and don't touch with oils, acids, alkalis
B. During the process of using on the spot,please must avoid touch with sharp hard objects.
C. Every time after pulling inflatable mandrel out the mold,please use brush(had better with nylon brush) and running water to wash, removing the concrete on surface in order to keep the mandrel clean.
D. If the mandrel leak gas and sealing film off,you can use grinding wheel to burnish at the place needed repair and then brush glue to cover the sealing film; for the damaged place of fiber, you should use tape to cover for repairing.
Q1: Are you factory or trading company?
A: Qingdao Aorunda Rubber Industry Co.,Ltd is the company and factory,located in Jimo City,Qingdao,near to Qingdao port and Qingdao airport,which is convenient for transportation.
Q2: What’s your delivery time and payment terms?
A: Delivery time is according to customers’ size and order qty.The payment terms you could choose are T/T,L/C at sight,Western Union and so on.
Q3: What about your warranty time?
A: Our warranty period is 24 months.During this time,any problems about products from our factory,we solemn promise to change and repair them for free;if problems from customers’ improper operating,we could provide free guidance and repair materials
Contact Person: Ms. qiu